Home > Kits > AddiKits >

Breadboard Prototyping AddiKit: Breadboard with 3.3V/5V Power Module and Jumper Wires
Breadboard AddiKit with 830 Hole Breadboard and Power Supply and Jumper Wires

Price: $13.50
Sale Price: $11.50
Savings: $2.00

Quantity in Stock:( Out of Stock )

Availability: Ships same day*
Product Code: AD144

Product Contents:

  • 1 pc - 830-hole breadboard with adhesive backing
  • 1 pc - 5V, 3.3V breadboard power supply module (style may vary from picture above)
  • 1 pc - USB cable with male A to male A connectors
  • 1 pc - Formed breadboard jumper wire kit (140 pieces)
  • 1 pc - Bundle of flexible jumper wires (65 pcs)
  • All of the above comes in a Addicore reusable AddiKit box

  • Breadboard:
    • Accepts most electronic components, including integrated circuits and transistors for digital and/or analog circuitry
    • Has 0.1" hole spacing, with 4 power buses, 10 columns and 63 rows, with 830 tie points total; pins are identified by numbered rows and lettered columns
    • Size: 6.5in (16.51cm) length x 2.125in (5.358cm) width; interlocking parts allow for multiple boards to be connected
    • Power rails: 8 total power rails, with 2 negative and 2 positive on each long side of the breadboard; each rail has 25 tie points
    • Includes two sets of five columns separated by approximately 0.3", allowing for straddling of a DIP package over the gap
  • Power supply module:
    • Includes two-way independent control and can be switched to 0V, 3.3V, and 5V
    • Barrel Jack Input voltage: 6.5V-12V DC
    • USB Jack:
      • Input voltage: 5V
      • Output voltage: 5V (when module is powered through barrel jack)
    • Output voltage: 3.3V, 5V DC
    • Output current: 700mA
    • Includes two sets of 3.3V, 5V DC output pins that connect to an attached breadboard's power rails
  • USB cable:
    • Length: 13.5in (34.29cm)
    • Male A to Male A connectors
    • Compatible with standard USB wall adapters
  • Pre-formed jumper wire kit:
    • Includes 140 #23 AWG jumper wires with 14 different lengths and 10 pcs per length
    • All wires included in a frosted plastic case
  • Flexible jumper wire bundle:
    • Includes 4 extra-long wires (8-3/8in / 21.27cm), 4 long (6-1/2in / 16.51cm), 8 medium (4-7/8in / 12.38cm), and 49 short (3in / 7.62cm)
    • Diameter of end pins: 0.23in (0.58mm)
  • Can use kit to prototype and test circuit designs
  • Recommendations for use:
    • Use a USB wall adapter, such as one used to charge a cell phone, with the included USB cable to power the module and breadboard
    • The 5V output of the module does not have any overcurrent protection between it and the 5V line of the USB jack, therefore we recommend using wall adapters to power the module through the USB connector because most standard USB wall adapters include built-in overcurrent protection
    • The USB jack can be used as a power output when powering the module though the input barrel jack (ex: you can attach an Arduino's USB cable to the USB jack on the power module and use the power module to power the Arduino); the total cumulative current drawn from the USB jack and the breadboard power rails must not exceed 700mA
    • IMPORTANT: it is not recommended to plug the USB cable into a computer to power the module because in the event that you do overcurrent or short the 5V line, the only thing protecting your computer is the circuit protection built into your computer's USB port

Average Rating: Average Rating: 4.5 of 5 4.5 of 5 Total Reviews: 13 Write a review

  0 of 0 people found the following review helpful:
3 of 5 Purchased for possible future use September 12, 2019
By: John Goodman from Garden Grove, CA United States  
I have not yet tried doing anything with this item, but I got it since it looked interesting, and I plan to explore what I can do with it later on.

Was this review helpful?

  0 of 0 people found the following review helpful:
5 of 5 Nice TTL interface kit. June 24, 2019
By: Kevin R. Hardy from San Diego, CA United States  
Easy to breadboard 5v TTL driven circuits.   Product is well built and easy to manipulate for circuit development and testing.

Was this review helpful?

  0 of 0 people found the following review helpful:
4 of 5 Good value, but beware July 7, 2018
By: Ike Kaiser from Brockville, ON Canada  
Good starter kit, or for re-supply.  For the power module, I wish I could have put photos in here.  My modules ALL have voltage reversed.  Installed on the breadboard the positive is supplied to the blue rail, and Negative to the red rail.  Not a problem if you remember this throughout your build, but easily confused if at any point you fail to pay attention.  Photos would have proven that I tested this carefully, and repeated it with separate modules and with different DMMs.  Beware!

Was this review helpful?

  0 of 0 people found the following review helpful:
4 of 5 Good for 3.3v/5v; Standard Breadboard; May 4, 2018
By: Noah Koeppel from San Pablo, CA United States  
I wish I could also choose Vin as one of the rails but otherwise works as advertised. Breadboard is good. Jumpers flexible.

Was this review helpful?

  0 of 0 people found the following review helpful:
5 of 5 Low cost! Used w/ Particle Photon March 15, 2018
By: Christopher Uribe from San Diego, CA United States  
I'm using this to create a prototype for my smart water irrigation system. It's nice to know it all works before I solder everything together. This board has worked very well, so far. I really like that it provides both 5V and 3.3V power. :) Thanks, Addicore!

Was this review helpful?

View All Customer Reviews

Browse for more products in the same category as this item:

Kits > AddiKits
All Products
Electronics > Jumper Wires & Cables
Electronics > Breadboards
Electronics > All Electronics
Top Sellers