Home > Electronics > Modules & Shields >

New!  4 Channel Relay Module
4 Channel Relay Module


 
Alternative Views:


Price: $5.48
Sale Price: $4.45
Savings: $1.03


Availability: Ships same day*
Product Code: AD125


AD125 Size:


Qty:  
Info
 

4 Channel Relay Module. Uses optocoupler driven relays to switch higher voltage and/or current applications with an Arduino, Raspberry Pi, Beaglebone, or other microcontroller or ARM boards.

Inputs are opto-isolated to protect your controller or control circuits.

Inputs are active low triggered -- to activate one of the relays requires the input pin being pulled to ground (GND).

You can find 3D printable enclosures for this module on Thingiverse, such as this 4-Channel Relay Module Case.

WARNING: The screw terminals and relay solder connections are exposed on the bottom of the board. Caution must be used especially when using this module with high voltages, such as mains power or any voltages greater than 12V. Always disconnect high voltage from the module before wiring or touching the module. When high voltage is supplied to the module be sure to refrain from touching or pointing to any part of the module. Working with high voltages should only be undertaken by experienced individuals.
Product Contents:

  • 1 — 4 Channel Relay Module
Specifications:

Supply Voltage 3.75 to 6 V
Supply Current with Relays De-Energized 0.1 mA
Supply Current with 1 Relay Energized 68 mA
Supply Current with 2 Relays Energized 127 mA
Supply Current with 3 Relays Energized 182 mA
Supply Current with 4 Relays Energized 231 mA
Input Control Signals Active Low
Input Control Signals Current 1.95 to 2 mA per Channel
Relay Max Contact Voltage 250 VAC or 30 VDC
Relay Max Contact Current 10 A
Dimensions
Size Option
1
2
3
Length 72 mm (2.83") 75.5 mm (2.97") 75 mm (2.95")
Width 52 mm (2.04") 55 mm (2.17") 50 mm (1.96")
Height 17 mm (0.67") 17 mm (0.67") 17 mm (0.67")

Recommended Accessories
Male-Female Jumper Wires - 40 x 200mm (7.8in) 1 Channel Relay Module (Active Low Control) Female-Female Jumper Wires - 40 x 200mm (7.8in)
Price: $2.89
Price: $1.45
Price: $2.89
Male Female Jumper Wires - 40 x 200mm (7.8in) 1 Channel Relay Module (Active Low Control) Female-Female Jumper Wires - 40 x 200mm (7.8in)

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 9 Write a review

  0 of 0 people found the following review helpful:
 
4 of 5 Unpowered early review May 1, 2020
By: Stephen Young from Vancouver, BC Canada  
Nice and compact quad module.  A nice touch is a mechanical isolation between the output commons (the relays are Form C / SPDT) and the coil pins, via a PCB cut-through.  Another level of isolation is electrical, you can have a different 5VDC feed to drive the relay, but the DC Common is always common, so not a fully isolated set-up, i.e., keep them power supplies clean and them DC Common lines thick and intelligently routed.
Another good thing about the board are the indicating LEDs, nice touch.  4 mounting holes, a bit too near the components?
Full disclosure:  I have yet to power them up.

Was this review helpful?

  1 of 1 people found the following review helpful:
 
5 of 5 4 channel relay November 27, 2018
By: Michael Pruitt from Charlotte, NC United States  
Very happy with this module due to small footprint, very simple interface, and great price!

Was this review helpful?

  0 of 0 people found the following review helpful:
 
5 of 5 April 11, 2018
By: Anonymous Person from MO United States  


Was this review helpful?

  1 of 1 people found the following review helpful:
 
5 of 5 Great buy! Used w/ Particle Photon March 15, 2018
By: Christopher Uribe from San Diego, CA United States  
I'm using this to route power to several solenoid valve's that intelligently open and close to allow water to run to my tape irrigation for my vegetable garden. I have four zones that have been happily watered and it was all thanks to this 4-Channel Relay Module. Thanks, Addicore!

Was this review helpful?

  1 of 1 people found the following review helpful:
 
5 of 5 Great relay board! February 10, 2017
By: ovide mercure from boca raton, FL United States  
Using this for a fill flush hydroponics control system.  Over 5000 cycles and not a single blip.  Current draw reported on specification table are completely accurate.  Great board.

Was this review helpful?

View All Customer Reviews

Browse for more products in the same category as this item:

Electronics > Modules & Shields
Electronics > All Electronics
Electronics
All Products
Top Sellers
Sale!
New Products